Hey, I bought a Sharp GF9797 with original Box and didn't expect much because I knew the GF8787 and 8989. So after I received it, I serviced the tapedeck (although it supririsingly worked well out of the box but I don't trust old rubber parts), adjusted everything and was not disappointed but a little bored. It sounded… boring. Then I thought how could the GF9595 and GF9191 with similar speakers be so Bass Heavy and another one for over 1000 bucks which is newer so tinny. Did they do it because they spent so many costs on the PLL Tuner that the Speakers are not good enough? Did they want to make it as efficient as it could be for a long battery life in times of expensive and bad batteries, or did they just castrated it to give people a reason buying the bigger models? I didn't find the answer, but I made measurements. First thing I tried was using an external source (Computer), adding an EQ and just turn up the lower Frequencies around and under 60 Hz. I played a sweep and also listened to music. Then I noticed that the speakers were able to reproduce frequencies to down around 45 Hz very clean. Original there was some punch but only when the Bassdrum was not too deep. Then I used the phones out to measure the Frequency response with Bass on Full and Lower Volume to get the Loudness Curve. I did the same on the GF9000. I noticed that the Loudness Curve of the GF9797 was much more neutral than the one of the GF9000 or also the 9191. On the beginning I thought they just didn't add loudness for cutting costs, because it sounded so thin. So then I thought… what if we could just make the Loudness better. It's a very simple circuitry just a resistor and a cap per channel. So without changing the original resistors I added a 50 kOhm Stereo Pot I had laying around to R417 and 418 and just turned it in both directions until the GF9797 sounded more satisfying. I measured around 1,5 kOhm instead of the original 3,9 kOhm. Keep in mind that you don't make anything louder with it. The Mids and Highs become quieter in comparison to the Lower End so you get more Bass Response without damaging anything because of higher gain and you don' loose the maximum Volume because the Loudness fades on the higher positions of the volume pot. At first I thought "That's it, it's much better…". Then I noticed that it was almost the same like original: I had a lot of punch now, but only in the upper Bass around 70-100 Hz, so when the Bassdrum was tuned a bit deeper it was practically gone and you just had this hummy bassline sound. So then I thought we need to open the lower end through the bass pot. So I added 30 nF ceramic caps to C413 and 414 to the existing 33 nF (so we have 63 nF now on both) and 20 nF to C411 and 412 (so now we have 35 nF on each). The board looks like shit now because I didn't want to remove it (they are all directly behind the Volume and Bass Pots) and I just had very big ceramic caps with 10 nF so I needed to take a lot of them and experiment to come to a satisfying result and of course you can disassemble the board and replace the original parts directly against the fitting values which would look much nicer… fortunately nobody will ever see it ^^ and as long as it works nobody cares. The Falldown under 70 Hz is now deeper. I only have under 1 dB between 80 and 50 Hz, which was around 3,5 dB before, that's a lot because you need to think in Stereo so we have a loss of around 7 dB in Bass compared to higher frequencies. But yeah the result is the GF9797 sounds now as it looks. It has a lot of bass and punch without distorting too early and the mod is done fast if you are already on the way to service it. So this modification is transferable to every other boombox as long as the speakers can handle the lower frequencies well. A second thing was that I didn't like the highs. The tweeters of the GF9797 sound a bit scratchy and not very detailed, so I replaced them against Hertz DT24.3 . They sound a lot better in the upper highs and have a very good SNR (94 dB) for their price. Also I bridged the Resistors R807 and R808 to make them as loud as possible. You also can do this with the original tweeters but I am not sure if they could get damaged then if you listen very loud. It sounds very detailed and bright now in highs but I think it's very important for a mobile device to have a bit headroom depending on where you use it. Most devices sound too muffled when they stand on the floor so if it's too much you can always turn the Treble or Bass Pot down but you can never get more, if the pots are on max and it still sounds unsatisfying. Also it's really worth on every boombox to check if you can improve the tweeters. I was so disappointed by the GF9191 and always thought the speaker set is completely crap, then I just replaced the tweeters with JVC RC 70 tweeters I had laying around and holy shit…. since then I love it. It has such a nice low end but now it also has detailed and bright highs and almost sounds like the M70. With better tweeters it is maybe the best box at its age. May I should check the GF9000, may there is headroom on the low end and it could be that it's not the speakers fault…. Also curious about the GF555/666, I don't have one but we all know it should sound much bigger than it does... Cheers Tobi
I wish I had more time to do fun stuff with my equipment. I do know that with most of my past purchases, a good cleaning of the FUNCTION switch helps bring back a lot of fidelity. The GF9797 is a little different with individual buttons; I don't know how to address those. I don't think too much about boombox tweeters, I always expect that they just add high pitch screeching but some boomers do have decent small drivers. I'll take an empty paper towel roll and listen at a low volume to see how clear the sound is and unfortunately screeching seems to be the rule.